Manual TP298
10 TP2983. Safety information 3.1. General information ATTENTION! • This device may be used exclusively for the inscription of labels, endless pape
11 TP2984. Scope of delivery Please verify the printer condition immediately after its arrival to determine any po
12 TP298
13 TP2985. Printer installation - printer configuration ATTENTION! Never position the printer in a location where
14 TP2985.3. USB interface Connect the computer to the USB interface of the printer, using the supplied A-B cable. Upon initiation of the printer, t
15 TP298Within the first setting, you may activate or deactivate "DHCP", respectively. For changes, press
16 TP298The cutting blade is provided with two longer guiding pins on the rear. Make sure that these pins are seated in the bores of the printer enclo
17 TP298 Pull the print roller from its guidance. Slide the other roller into the guidance. Replace the cover a
18 TP298
19 TP298 Fixate the ink ribbon by attaching an adhesive strip to the cardboard core 1 on the front transport rolle
List of Contents 1. Useful start-up information 4 1.1. Start-up support 5 2. General information / product description
20 TP298 Guide the strip above the pin and between the two strip guide rails. Then re-adjust the sensor. The strip must be guided between the sens
21 TP298 The following illustration shows an overview of the whole progress of the marking strip. Sensor
22 TP298 Now move the lever clockwise to its limit stop. This puts the print head in its printing position.
23 TP2986.4. Loading the WMB Inline Make sure that the device is turned off. The insertion of the WMB Inline (200
24 TP2987. Printer driver installation 7.1. Printer driver installation There are 3 options to control the TP298: 1. via the USB interface (not pos
25 TP298 Please select the connection type: USB COM Network
26 TP298 The status monitor is not mandatory for the driver operation and may be installed when required. The installation of the printer driver is c
27 TP2987.2. Printer driver settings for marking strips In the Windows Printers folder, right-click on the corres
28 TP298 These settings have been tested for the application of a cutting knife (Item No. 258-161). If you do not use a cutting knife, please activat
29 TP298
8. WAGO ProServe software 31 8.1. Installation of ProServe software 31 8.2. Design and inscription with smartDesigner 31 8.3. Insc
30 TP298Advanced printer settings WMB Inline (Item no. 2009-115): The print head offset is preset for the use wi
31 TP298 8. WAGO ProServe software The following section introduces two other components of the ProServe CD: the p
32 TP2988.2.2. Planning Direct input of article number - click on "ADD" Via Drag & Drop from the library tree / index Via Drag &
33 TP298 8.2.3. Inscription of planned terminal blocks First deactivate the item Activation of font size check
34 TP298 • Either direct input of inscriptions in the table, or selection of cells of the inscription table and inscription using the Wizard
35 TP298DESCRIPTION OF PARAMETERS Distance to left edge The distance to the left edge is variable and depends on t
36 TP298Number of print-outs (= Number of copies) Print separating line The separating lines can be deactivated here. Printer selection Here you act
37 TP298 First, you click on the tab "Printer" and select the corresponding driver by clicking on t
38 TP2989. Printer maintenance 9.1. General The printer requires little maintenance. A regular cleaning of the print head is very important. Only thi
39 TP298We recommend the following cleaning intervals. Thermal transfer print – marking strips 2009-110: to be cle
4 TP2981. Useful start-up information Dear customer, We are happy about your decision to utilize the WAGO thermal transfer printer TP298. In additi
40 TP29810. Frequent questions Fault Possible cause What to do Printer does not react Printer is not turned on Check the power supply and turn on
41 TP29811. Registration form If you cannot find the registration form for the printer, please complete this form a
42 TP298 WAGO Kontakttechnik GmbH & Co. KG P.O. Box 28 80, D-32385 Minden Hansastraße 27 · D-32423 Minden Phone ++49/571/ 887-0 Fax
5 TP2981.1. Start-up support This section contains information required by you to begin working with WAGO inscript
6 TP298
7 TP298Immediately prior to printing a marking strip from the smartDESIGNER, we would like to suggest the following
8 TP298After some seconds, the FEED button will light up in green. Push the FEED button once. The printer will measure the existing labels within seco
9 TP2982. General information / product description 2.1. General information By purchasing the innovative WAGO in
Comments to this Manuals